1. Reasons for the switchboard: The slider or the chute wears; the fixed bolts at the two ends of the door are loose; the doorway is deformed; the lift is too high; the caster wheel is rusted; and the caster wheel screw is deformed. Remedy: First replace the roller and screw, and then check the slider chute, if serious wear and tear, should be replaced; Correction of the door fixing screw; If the door is fixed at wear, you can add a rectangular gasket; When the handle is too high, use Lift the handle and lift the front end with a new bumper. 2. Causes of non-operation: The pin or screw shaft is worn out; the sliding sleeve fixing bolt is missing. Remedy: Open the working gear cover, replace the finger pin or screw shaft; if the slide sleeve fixing bolt is missing, it should be reinstalled. 3, the separation needle hit the door reason: dislocation of the fontanelle; improper installation of planting arms; planting arm crank bore wear; separation needle upturned; take the amount of adjustment is too large; rocker shaft turbulence or wear down hole. Remedy: Reset the fontanelle and fix it; adjust the planting arm to the correct position; replace the worn crank or chain shaft; correct or replace the separation needle; replace the pendulum shaft or bearing shaft and bearing; 4. The reason why a group of planting arms do not work is that the chain box drive shaft is broken; the chain is out of stock or broken. Remedy: Attach the chain; replace the drive shaft. 5, send 秧 lift the back end is too high Cause: The rubber buffer block is missing or damaged. Remedy: Pick up the front end of the handle with a screwdriver and install a new bumper. 6. The reason why the crucible shaft does not rotate is that: the ratchet wheel wire pin falls off; the ratchet wheel groove wears; the pawl or the torsion spring falls off; and the crucible shaft shaft moves. Remedy: First see if the ratchet, pawl and torsion spring are intact. If they are damaged or fall off, they should be replaced. Then turn the feed screw, if the ratchet rotates and the feed shaft does not turn, it means that the steel wire pin is off and the steel wire pin is installed. complex. 7. The reason for the small rotation angle of the feed shaft is that the peach wheel and the feed cam wear badly. Remedy: Open the working gear cover and replace the new one. 8. The reason why the main clutch is not completely separated is as follows: the friction sheet is stuck on the pulley; the positioning screw is loose, causing the clutch pin to fall off; the clutch pin is seriously worn. Remedy: Remove the pulley assembly, make the adhesive part off, use sandpaper to clean the friction plate saw, replace the clutch pin; tighten the set screw. 9. Incomplete separation of the positioning clutch Cause: Improper adjustment of the adjustment nut; separation pin and adjusting nut sliding buckle; positioning convex edge wear on the clutch teeth; tension spring broken (positioning clutch using shift fork). Inspection method: first open the positioning and separation cover, check whether the adjusting nut is in the correct position, whether the adjusting nut and the separating pin are slipped, and whether the extension spring is broken. If there is no problem and then remove the power output shaft assembly, check the technical state of the teeth embedded positioning flange. Remedy: Adjust the adjusting nut to the correct position; separate the pin or adjusting nut sliding button should be replaced; replace the tension spring; if the positioning convex edge is worn, the separating teeth can be meshed off about 0.5 mm; severe wear should be replaced. 10. The reason why the feeding shaft does not work is that the peach shaped wheel positioning key is damaged or missing; the peach shaped wheel is stuck with the feeding cam; the feeding cam wire pin is broken or missing. Remedy: If two cards are in phase, it is due to the wear of the shuttlecock and the peach-shaped wheel. The delivery cam or peach-shaped wheel can be removed and the working surface can be smoothed with a guillotine blade. The severe wear should be replaced. If the key or pin is damaged, replace it with a new one. 11. Reasons for the intermittent operation of the squeezing shaft: The return force of the peach-shaped wheel return spring or the delivery cam return spring is weak, so that the peach-shaped wheel or the delivery cam cannot return. Remedy: Open the working gearbox cover, remove the two return springs and replace the new return spring. 12, positioning clutch handle stuck reason: After the separation cam wear, with the adjustment nut stuck. Remedy: Remove the separation cam and use a grinding wheel or file to grind the cam face into a smooth arc.
Pain Relief Patch for neck shoulder, lower back and leg.
Pain Relief Patch For Neck Shoulder,Lower Back And Leg Pain Relief Patch,Pain Relief Pad,Pain Relief Plaster,Neck Pain Relief Patch,Back Pain Relief Pacth Shandong XiJieYiTong International Trade Co.,Ltd. , https://www.xjplaster.com
[Name] Medical Cold Patch
[Package Dimension] 10cm×12cm 2pieces/box
The pain relief patch is composed of three layers, namely, backing lining, middle gel and protective film. It is free from pharmacological, immunological or metabolic ingredients.
[Scope of Application] For cold physiotherapy, closed soft tissue only.
[Indications]
The patches give fast acting pain relief for strains, sprains, cramp, bruises, swollen areas or joint stiffness.
[How To Use a Patch]
Tear off the packaging bag and remove the patch. Remove the protective film and apply the patch on the skin. One piece, one time. The curing effect of each piece can last for 8-12 hours.
[Attention]
Do not apply the patch on the problematic skin, such as wounds, eczema, dermatitis,or in the eyes. People allergic to herbs and the pregnant are advised not to use the medication. If swelling or irritation occurs, please stop using and if any of these effects persist or worsen.notify your doctor or pharmacist promptly. Children using the patch must be supervised by adults.
[Storage Conditions]
Store below 30c in a dry place away from heat and direct sunlight.